8/2/2023 0 Comments 777 cockpit layoutIts development cost could be over $5 billion with at least $2 billion for the carbon-composite wing. The design work is distributed between Charleston, Huntsville, Long Beach, Philadelphia, and St. On May 1, 2013, Boeing's board of directors approved selling the 353-seat 777-8LX to replace the 777-300ER from 2021, after the larger 406-seat -9X. In 2012, with the Boeing 737 MAX in development and the 787-10 launch in preparation, Boeing decided to slow 777X development to reduce the risk with introduction still forecast for 2019. Model at the February 2014 Singapore Airshow Pratt and Whitney said: "Engines are no longer commodities.the optimization of the engine and the aircraft becomes more relevant." Launch Airbus points out that handling more than one engine type adds millions of dollars to an airliner cost. Some customers bemoan the loss of engine competition, like Air Lease Corporation's CEO Steven Udvar-Hazy who wanted a choice of engines. In March 2013, Boeing selected the GE9X with a 132 in (335 cm) fan. GE Aviation proposed the GE9X with a 128 in (325 cm) diameter fan, a 10:1 bypass ratio, a 60:1 overall pressure ratio, and 27:1 HP compressor ratio for a 10% fuel burn reduction. Pratt & Whitney responded with the 100,000 lbf (440 kN) thrust PW1000G geared turbofan architecture. Rolls-Royce Plc proposed its RB3025 concept with a 132 in (335 cm) fan diameter, a 12:1 bypass ratio, and a 62:1 overall pressure ratio, targeting a fuel burn of more than 10% lower than the GE90-115B and 15% lower than its Trent 800 powering the 777 the RB3025 concept has a composite fan, a core derived from the Trent 1000, and advanced HP materials. The General Electric GE90-115B of the earlier 777-200LR and -300ER variants has a 42:1 overall pressure ratio and 23:1 HP compressor ratio. Horizontal stabilizers would be extended. It would fall into ICAO aerodrome code F like the 747-8 and A380 but with 22 ft 6 in (6.9 m) folding wingtips it would stay within the 213 ft 4 in (65.02 m) code E like current 777s. The current 777-200LR/300ER have a 775,000 lb (352 t) MTOW.Ī new carbon-fiber-reinforced polymer (CFRP) wing with a wingspan of 213 or 225 ft 2,560 or 2,700 in (65 or 68.6 m) with blended winglets, or up to 233 ft 5 in (71.1 m) with raked wingtip provide for a 10% larger wing area. The 407–passenger 777-9X should stretch the 777-300ER by four frames to 250 ft 11 in (76.48 m) in length, for a 759,000 lb (344 t) maximum take-off weight (MTOW) and powered by 99,500 lbf (443 kN) engines, targeting per-seat 21% better fuel burn and 16% better operating cost. In 2011, Boeing refined its response to the revamped Airbus A350 XWB with three 777X models, targeting a firm configuration in 2015, flying in late 2017 or 2018, and entering service by 2019. The 777-9 first flew on January 25, 2020, with deliveries delayed multiple times and expected to commence in 2025. As of February 2023, there are 363 total orders for the 777X passenger and freighter versions from ten identified customers and other buyers. The 777X program was proposed in the early 2010s with assembly at the Boeing Everett Factory and the wings built at a new building adjacent to the Everett factory. The 777-8 provides seating for 384 passengers and has a range of 8,730 nautical miles (16,170 km 10,050 mi) while the 777-9 has seating for 426 passengers and a range of over 7,285 nmi (13,492 km 8,383 mi). The 777X was launched in November 2013 with two variants: the 777-8 and the 777-9. The 777X features new GE9X engines, new composite wings with folding wingtips, greater cabin width and seating capacity, and technologies from the Boeing 787. The Boeing 777X is the latest series of the long-range, wide-body, twin-engine jetliners in the Boeing 777 family from Boeing Commercial Airplanes.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |